T8 LED Driver - DEK-T8HR-22W-480MA

1. Isolated or Non-isolated;, 2. High efficiency, High PFC;, 3. No Stroboflash;, 4. High reliability; Comply with EMC &. RoSH. - details see: https://www.lightinghere.com/t8-led-driver-10022118

Place of Origin: Guangdong China (Mainland)

Brand Name: DADEKAN

Model Number: DEK-T8HR-22W-480MA

MODEL					DEK-T8HR-22W-480MA
Input	Input Voltage				90VAC~277VAC
	VoltageRange				100VAC~277VAC
	Start-up Voltage(-25~70°C)				90VAC
	FrequencyRange				47Hz~63Hz
	Power Factor(@25°C)				>0.95@220VAC, Full Load
	AC Current(@25°C)				0.25AMax.
	Inrush Current(@ 25°C)				10AMax.
Output	OutputVoltage Range				30V~40V
	OutputCurrent				480mA
	OutputPower				10~22W
	ConversionEfficiency (@25°C)				86% @220VAC, Full Load
	No-load Output Voltage				50V Max.
	Line Regulation(@-25~70°C)				±5%
	Accuracy Constant(@-25~70°C)				±5%
	Set-up Time(@25°C)				<1S@220VAC,<2S@110VAC
	Temperature Coefficient(@-25~70°C)				±0.03%/°C
	Overshoot(@-25~70°C)				±5% No-load Rated Voltage
	Output Ripple & Noise			0<Ta≤70°C	130mVP-P
				-25≤Ta≤0°C	200mVP-P
Protection(-25~70°C)	Input Electrical		Low Voltage Protection		/
			Over VoltageProtection		/
	Output Electrical		Shorted Circuit Protection		Hiccup, Auto Recovery
			No-load Protection		Constant Voltage
	OverTemperatureProtection				/
Environmental Requirement	Vibration				10~500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z, axes
	Impact				20G/11mS pulse,3times at each X, Y, Z axes
	Storage Temp. & Hum.				-40°C~85°C; 10%~95%RH No condensing
	Operating amb. Temp. & Hum.				-40°C~60°C; 20%~90%RH No condensing
	Altitude				3000m
	IPX				/
Safety &. EMC	Isolation Resistance				Input--out: 100M OHMS
	Withstand Voltage				Input--out: 3KVAC/10mA
	Ground Impedance				/
	Safety Standards				IEC 61347-2-13/GB19510.14/UL8750
	EMI	CE			EN55015 Class B/FCC Part15 B
		RE			EN55015 Class B/FCC Part15 B
	Harmonic Current				EN6100-3-2, Class C
	EMS	CS			EN61000-4-6 Level 3 Class B
		RS			EN61000-4-3Level3Class B
		ESD			EN61000-4-2 Level 4
		Surge			EN61000-4-2Level 4
		Power Frequency Harassment			EN61000-4-8Level3
		EFT			EN61000-4-4Level3
		Interrupt, Drop			/
Other	Dimensions (L * W * H)				290mmX 17mm X 10mm
	Package				/
	Cooling Method				VentilationCooling
Reliability	Burn-in				The power supply shall go a minimum of 4 Hours burn-in test under full load condition.
	Design MTBF				50,000Hrs @25°C, MIL-HDBK-217 Method 2 Components Stress Method
	Design Electrolytic Capacitor Life				17520Hrs @50°CFull load and units continuously working
Note	Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 10uF parallel capacitor. Test spare parts: test voltage for 500 VDC, 65% RH @25°C. The SPS is considered a component which will be installed into final equipment. The equipment must be re-confirmed that it still meets EMC directives.
Minimum Negative Load Requirements	None
Accessories	/